Difference between revisions of "IPv6"

From Linux-VServer

Jump to: navigation, search
(Add IPv6 info)
 
(catspec)
 
(8 intermediate revisions by 5 users not shown)
Line 1: Line 1:
 
At the time of this writing, IPv6 support in guests requires you to apply an additional patch on top of the Linux-VServer patch. The IPv6 patch can be fetched from the official source: [http://people.linux-vserver.org/~bonbons/ipv6/ Bruno Prémont's IPv6 patches], and sometimes rediffs against later kernels are available from [http://people.linux-vserver.org/~dhozac/p/k/ my patch directory].
 
At the time of this writing, IPv6 support in guests requires you to apply an additional patch on top of the Linux-VServer patch. The IPv6 patch can be fetched from the official source: [http://people.linux-vserver.org/~bonbons/ipv6/ Bruno Prémont's IPv6 patches], and sometimes rediffs against later kernels are available from [http://people.linux-vserver.org/~dhozac/p/k/ my patch directory].
  
To use the patch, you need util-vserver 0.30.212 or newer. These versions support IPv6 natively, so you just need to put the address in <code>/etc/vservers/<guest>/interfaces/X/ip</code> and start the guest to get it an IPv6 address.
+
To use the patch, you need util-vserver 0.30.212 or newer. These versions support IPv6 natively, so you just need to put the address in <code>/etc/vservers/<guest>/interfaces/X/ip</code> and start the guest to get it an IPv6 address. You should also put "64" (or whatever bitmask has been assigned to you with your prefix) in <code>/etc/vservers/<guest>/interfaces/X/prefix</code>.
 +
 
 +
 
 +
Starting with linux-vserver-2.3 IPv6 support is included in the main source code. No need to apply any extra patches.  You will need to have util-vserver 0.30.214 or newer if you are using the 2.3+ patches.
 +
 
 +
==Dual-Stack==
 +
If you want both IPv6 and IPv4 addresses, just use IPv4 on one interface (e.g. interfaces/0) and create another interface (e.g. interfaces/1) with IPv6.
 +
 
 +
== Loopback isolation ==
 +
There is currently no loopback isolation (as it is for IPv4) available for IPv6.
 +
 
 +
[[Category:Network related]]

Latest revision as of 22:25, 21 October 2011

At the time of this writing, IPv6 support in guests requires you to apply an additional patch on top of the Linux-VServer patch. The IPv6 patch can be fetched from the official source: Bruno Prémont's IPv6 patches, and sometimes rediffs against later kernels are available from my patch directory.

To use the patch, you need util-vserver 0.30.212 or newer. These versions support IPv6 natively, so you just need to put the address in /etc/vservers/<guest>/interfaces/X/ip and start the guest to get it an IPv6 address. You should also put "64" (or whatever bitmask has been assigned to you with your prefix) in /etc/vservers/<guest>/interfaces/X/prefix.


Starting with linux-vserver-2.3 IPv6 support is included in the main source code. No need to apply any extra patches. You will need to have util-vserver 0.30.214 or newer if you are using the 2.3+ patches.

[edit] Dual-Stack

If you want both IPv6 and IPv4 addresses, just use IPv4 on one interface (e.g. interfaces/0) and create another interface (e.g. interfaces/1) with IPv6.

[edit] Loopback isolation

There is currently no loopback isolation (as it is for IPv4) available for IPv6.

Personal tools